Sprache:


CLM's Blog


Activated carbon has the highest use value

CLM
Without adding additives to the sludge, the concentration of sulfuric acid and zinc chloride is 4 mol·L' and the volume ratio is 2:1. The activated carbon prepared has the maximum iodine adsorption value of 549.6 mg·g 'and the yield of 51.3%, which is the better carbon sample prepared by pure sludge and is recorded as SAC.(3) Adding 8% peanut shell, the iodine value of activated carbon of sludge reached 789.6mg · g', which was recorded as PAC By single factor experiment, the optimal conditions of carbon production were obtained as follows: pyrolysis temperature 600℃, activator concentration 4 mol · L', pyrolysis time 1.5h, solid-liquid ratio 1:2.5.Orthogonal experiment showed that the influence of each factor was as follows: pyrolysis temperatureIs the activator concentration Pyrolysis time >Solid-liquid ratio.(4) the main performance of PAC is basically equivalent to 8818 type activated carbon; The concentrations of heavy metals in activated carbon leaching solution of sludge were all qualified.Compared with domestic and foreign research reports, the quality of PAC is in the middle level.(5) Compared with SAC, the specific surface area of PAC is larger, up to 636.8m2·g'. PAC is mainly mesoporous, but also contains some micropores. The adsorption/desorption isotherm shows that PAC is activated carbon with parallel wall slit pore structure.Its adsorption is selective, and non-polar substances are easier to be adsorbed than polar substances.In the same series of substances, the higher the boiling point of the substance, the more tolerantEasy to be adsorbed, the greater the pressure, the lower the temperature, the greater the concentration, the greater the amount of adsorption.On the contrary, decompression and heating are beneficial to gas desorption.It is often used for gas adsorption,Separation and purification, recovery of solvents, decolorizing agents for sugar solution, grease, glycerin, medicine, deodorant for drinking water and refrigerators, filter agent for gas masks,It can also be used as a catalyst or metal salt catalyst carrier.Early production of activated carbon raw materials for wood, hard nut shell or animal bones, later mainly used coal, after drying https://www.yrdcarbon.com/products/activated-carbon/ Distillation, activation treatment after the production of activated carbon methods are :① steam, gas activation method.Carbon is activated by water vapor or carbon dioxide at 850~900℃.The granular activated carbon with high strength was prepared by heating wood phosphate mixture at low temperature and using tar generated during its pyrolysis as binder. In this paper, the process conditions and plasticizing mechanism of granular activated carbon prepared by phosphoric acid were studied, which provided scientific data and theoretical basis for the preparation of high strength granular activated carbon. Fir chip as the raw materials, H - POs as activator, using single factor analysis and orthogonal experimental design method, this paper discusses the influence granular activated carbon pore structure and the iodine adsorption value, methylene blue and strength of various preparation factors, determine the optimum process conditions of preparation of granular activated carbon phosphoric acid, phosphoric acid concentration is 70%, dipping 180%, kneading temperature is 170 ℃, for 60 min kneading time, activation temperature is 350 ℃, the activation time of 210 min. https://www.yrdcarbon.com/

The best source of activated carbon

CLM
ol·L' and the volume ratio is 2:1. The activated carbon prepared has the maximum iodine adsorption value of 549.6 mg·g 'and the yield of 51.3%, which is the better carbon sample prepared by pure sludge and is recorded as SAC.(3) Adding 8% peanut shell, the iodine value of activated carbon of sludge reached 789.6mg · g', which was recorded as PAC; [url=https://www.yrdcarbon.com/]www.yrdcarbon.com[/url] By single factor experiment, the optimal conditions of carbon production were obtained as follows: pyrolysis temperature 600℃, activator concentration 4 mol · L', pyrolysis time 1.5h, solid-liquid ratio 1:2.5.Orthogonal experiment showed that the influence of each factor was as follows: pyrolysis temperatureIs the activator concentration Pyrolysis time >Solid-liquid ratio.(4) the main performance of PAC is basically equivalent to 8818 type activated carbon; The concentrations of heavy metals in activated carbon leaching solution of sludge were all qualified.Compared with domestic and foreign research reports, the quality of PAC is in the middle level.(5) Compared with SAC, the specific surface area of PAC is larger, up to 636.8m2·g'. PAC is mainly mesoporous, but also contains some micropores. The adsorption/desorption isotherm shows that PAC is activated carbon with parallel wall slit pore structure.According to the adsorption duration used in the experiment and the appropriate value of n (in the calculation process, when the adsorption duration is 30 min, n=480[url=https://www.yrdcarbon.com/products/activated-carbon/]activated charcoal wholesale canada[/url]

Product specifications of special activated carbon

CLM
The preparation methods of activated carbon include physical method, chemical method, microwave radiation method, etc.(1) Physical method.[url=https://www.chinactivecarbon.com/]chinactivecarbon.com[/url] Physical method is to use carbon dioxide, water vapor or the mixture of both as activator, the carbonized carbon material and gas in the activation furnace at 500~1200℃ for carbon activation reaction, so that the pore size of the carbonized material to expand, the formation of activated carbon with porous microcrystalline structure.Gas activation method mainly includes carbonization and activation engineering.The so-called carbonization, refers to the low temperature (about 500℃) is small, the volatile coal tar molecules in the material and the thermal decomposition and curing process of asphalt, that is, to remove the volatile in advance, made suitable for the next step of activation with carbonization.When the adsorption time is 85 min, take n-600), and the calculated theoretical curve is shown in FigureIt can be seen from the figure that the measured curve is in good agreement with the theoretical curve.Fig. 2 is the simulation result of the total number of Y taken out over time after activated carbon adsorbs 1 radon atom from the environment every second and continues to adsorb for 3 days.After the activated carbon was taken out, the total number of V reached the maximum after t time, and then the total number became smaller. After about 50 min, the total number of V decreased by a negative exponential function. The curve can be divided into a stationary area and a measuring area. The width of the stationary area the duration of the stationary area) is set at (t+50) min, followed by the measuring area.[url=https://www.coconutactivatedcarbon.com/]yrd coconut carbon[/url] There is no obvious rule of counting in the standing zone. Should be avoided during this period of time.Total number of;The measurement area is counted byIts adsorption is selective, and non-polar substances are easier to be adsorbed than polar substances.In the same series of substances, the higher the boiling point of the substance, the more tolerantEasy to be adsorbed, the greater the pressure, the lower the temperature, the greater the concentration, the greater the amount of adsorption.On the contrary, decompression and heating are beneficial to gas desorption.It is often used for gas adsorption,Separation and purification, recovery of solvents, decolorizing agents for sugar solution, grease, glycerin, medicine, deodorant for drinking water and refrigerators, filter agent for gas masks,It can also be used as a catalyst or metal salt catalyst carrier.Early production of activated carbon raw materials for wood, hard nut shell or animal bones, later mainly used coal, after drying

Activated carbon reinforcement

CLM
When the temperature is below 600℃, the specific surface area of carbonized material increases with the increase of temperature.When 600~900℃, the specific surface area reaches a certain value: 250~300 m2/g; when above1000℃, the specific surface area shrinks rapidly. When the carbonization temperature is above 800℃, the reaction performance of carbonized compounds and activation gas gradually becomes weaker, so the carbonization temperature is generally below 1000℃. However, if the residual volatile content and thermal effect are taken into account, the most suitable temperature should be 600~700℃39].activated charcoal wholesale canada The carbonized substance obtained from the carbonization process is placed in water vapor or a mixture of water vapor and combustion gas and heat treated at 800~1000℃, which is called the activation process.When the radon adsorption coefficient of activated carbon is constant,n is proportional to the concentration of radon. In this case, Equation (10) represents the functional relationship among the total number of activated carbon V, radon concentration and adsorption (or exposure) time. Therefore, the concentration of radon in the environment can be calculated according to the total number of activated carbon and adsorption time.Simulation calculation and result analysis of total number of activated carbon According to Equations (5) and (10), a computer program can be written to calculate the relationship between the total number of Y in the process of radon adsorption on activated carbon and the relationship between the total number of Y after the removal of activated carbon and the change of time.href="https://www.yrdcarbon.com/">https://www.hslabrasive.com

Activated carbon removes magazine ingredients

CLM
The purification efficiency of activated carbon adsorption method is 99.2%~99.3%. For the treatment of large air volume and low concentration of organic waste gas, it is agreed that this method is the most mature and reliable technology at home and abroad, but the T art process is too long, the operation cost is high, and it is often more difficult to need a stable steam source. In view of these problems, combined with the characteristics of this graduation design and only body requirements, the use of activated carbon fixed bed adsorption system for industrial organic waste gas purification, the selection of honeycomb activated carbon as adsorbent.The process system is compact and integrated with adsorption and desorption.A systematic reaction mechanism of KOH activation of petroleum coke was proposed, and the formation of pores and the sources of Ho, H, CH and CO in the activation process were explained. The changes of pore structure and microcrystalline structure of activated carbon and the transformation of potassium hydroxide during activation showed that KOH first reacted with petroleum coke to transform into KCO and formed a preliminary pore structure. Meanwhile, it was proved that the newly generated potassium carbonate played an important role in the development of pore structure of activated carbon.[url=https://www.dxdcarbon.com/product-category/activated-carbon]activated carbon manufacturer[/url] But directly with K; CO, the activator, the activation of the burning loss rate is large. However, the pore structure of activated carbon was not developed, indicating that the newly formed potassium carbonate in the pore channels was more likely to react with carbon during the activation process of potassium hydroxide, and the pore structure was further developed. According to the standard Gibbs free energy of the reaction, K· Co; (or K;O) direct reaction with carbon is difficult to be carried out at the activation temperature of 730℃, indicating that they react with -CH- and -CHZ - in petroleum coke and play an activation role.The elemental potassium generated from the activation reaction intercalated and activated the petroleum coke, and the specific surface area of the activated product reached 98m'g1.XRD analysis showed that there were potassium to graphite intercalated compounds in the activated product.According to the study results of activation mechanism, the mixing of additive N can improve the dispersion of alkali and the activation of additive N at high temperature to improve the activation effect.Activated carbon with a yield of 68% and a specific surface area of 2532m'g can be obtained under the conditions of alkali-coke ratio of 3:1, activation temperature of 730℃ and activation time of 30 minutes.At the same time, the amount of hydrogen produced in the activation reaction is large, reaching 38cm'g 'min', and hydrogen can be separated and purified.[url=https://www.dxdcarbon.com/]https://www.dxdcarbon.com/[/url] Thus, a one-step process for the preparation of activated carbon with high specific surface area was proposed.Compared with the conventional method, the process reduces the production cost, shortens the production time, saves energy, and lays a foundation for further industrial production.The prepared petroleum coke based activated carbon was used as the carrier.The catalyst supported by Ni-Mo has similar hydrodesulfurization activity with commercial catalysts. The DBT conversion rate is more than 98% at 290℃ and the catalyst has high stability.The pore size distribution of petroleum coke based activated carbon with high specific surface area is mostly between 1.0~ 2.0nm. The methane storage experiment using this sample shows that it has a high methane storage performance: at 1.4 MPa, room temperature, the mass adsorption capacity of methane is 0.112 Gg '.

Indirect use of activated carbon

CLM
China is the world's largest coal producer, coal resources are rich, the variety is complete, with the production of ash sold in the P Urology Department for China's coal-based activated carbon production laid a foundation. China's activated carbon production coal is mainly concentrated in the northwest region, there are long bituminous coal, weak viscous coal and anthracite, due to the single coal properties of the restriction, China's coal-based activated carbon products are mostly in the middle and low grade products.Coal based activated carbon production in China, starting in the 1950 s, but slow to develop early in the early 1980 s the national annual production of about 4 000 t [2 l. Along with the reform and opening up, economic development and the gradual improvement of the people's living standard and increasing efforts in environmental protection at home and abroad in recent years, domestic demand of activated carbon, and exports continue to increase, coal based activated carbon industry is developing rapidly. In the late 80 s, China's coal-based activated carbon produced more than 20000 tons, in 2000 reached 100000 tons, 400000 tons in 2008 or so,China has basically formed an independent, complete and initial industrial system for the preparation of activated carbon, and has become the world's largest producer of coal-based activated carbon.Due to the advantages of coal resources and product price, China's coal-based activated carbon products have a strong competitiveness in the international market.[url=https://www.dxdcarbon.com/product/activated-carbon-for-gold-recovery]activated carbon for gold mining[/url] At present, about 80% of China's coal-based activated carbon products are exported, and it is the largest coal-based activated carbon exporter in the world. Shanxi and Ningxia account for about 90% of China's coal-based activated carbon production and 80% of the export of coal-based activated carbon.Therefore, the production of coal-based activated carbon products has a broad prospect and is expected to achieve good economic benefits in the regions with rich raw material resources.At present, the production of coal-based activated carbon is mainly in Shanxi, Ningxia and Henan.The production of activated carbon with nut shell as raw material is mainly in hebei province; the production of activated carbon with wood as raw material is mainly concentrated in fujian, jiangxi, southern zhejiang and northeast region.In recent years, has gradually formed to Henan Changge City, Ningxia Yinchuan City and surrounding areas, Shanxi Datong region as the representative of the "three" activated carbon production base.Ningxia Yinlong Activated Carbon Co., Ltd. is the largest active carbon manufacturer in Asia with an annual output of 50,000 tons.Ningxia Huahui Activated Carbon Co., Ltd. manufactures a wide variety of activated carbon products and some of the performance of the products up to the world's advanced level.[url=https://www.chinactivecarbon.com/]activated carbon suppliers in china[/url] Shenhua Ningxia coal industry taixi charcoal based company activated carbon plant in recent years also determined to establish the world's largest activated carbon production base, the activated carbon industry will develop into one of the four pillar industries of Ningxia coal industry.

The development of activated carbon industry

CLM
largest coal-based activated carbon exporter in the world. Shanxi and Ningxia account for about 90% of China's coal-based activated carbon production and 80% of the export of coal-based activated carbon.Therefore, the production of coal-based activated carbon products has a broad prospect and is expected to achieve good economic benefits in the regions with rich raw material resources.At present, the production of coal-based activated carbon is mainly in Shanxi, Ningxia and Henan.The production of activated carbon with nut shell as raw material is mainly in hebei province; the production of activated carbon with wood as raw material is mainly concentrated in fujian, jiangxi, southern zhejiang and northeast region.In recent years, has gradually formed to Henan Changge City, Ningxia Yinchuan City and surrounding areas, Shanxi Datong region as the representative of the "three" activated carbon production base.Ningxia Yinlong Activated Carbon Co., Ltd. is the largest active carbon manufacturer in Asia with an annual output of 50,000 tons.Ningxia Huahui Activated Carbon Co., Ltd. manufactures a wide variety of activated carbon products and some of the performance of the products up to the world's advanced level. Shenhua Ningxia coal industry taixi charcoal based company activated carbon plant in recent years also determined to establish the world's largest activated carbon production base, the activated carbon industry will develop into one of the four pillar industries of Ningxia coal industry.This also promotes the formation of large-scale production of activated carbon at home and abroad.There are many kinds of activated carbon products, according to raw materials can be divided into: coal based activated carbon, wood activated carbon, nut shell activated carbon and synthetic activated carbon.Due to the demand of environmental protection, the production of wood activated carbon is subject to more and more restrictions.pellets carbon Wood activated carbon in China since the 1970 s, the proportion of total domestic activated carbon production of 80% to 40% of the 90 s, but our country coal resources are relatively abundant, variety complete, and low cost, stable and reliable supply, taking coal base as raw material to the production of coal based activated carbon percentage rise gradually, in the 1970 s and 90 s, coal-based activated carbon in China increased from 15% to 60% of the total amount of active carbon, and present a trend of increasing 1 all the time.activated coconut charcoal wholesale Therefore, the preparation technology of coal based activated carbon has been widely valued at home and abroad, and has made great development.At the same time, it has improved the performance of coal-based activated carbon products and become the world's largest activated carbon product in terms of production and consumption, accounting for about 70% of the total output of activated carbon in the ancient world.However, due to the protection of the environment and high-quality coal and wood resources, some developed countries have introduced relevant laws and regulations to limit the production of high pollution and high energy consumption of activated carbon, resulting in the production and export of activated carbon gradually reduced;On the other hand, because activated carbon is a resource-consuming, labor-intensive product, the production cost of activated carbon produced in developed countries is high, and its competitiveness in the international market is gradually declining.The activated carbon exported by China is mainly of middle and low grade varieties, with low added value. In order to occupy the international market share, enterprises generally adopt low-price marketing strategy, resulting in the low price of activated carbon in the international market.Statistics show that at present, the average price of China's exported activated carbon is only one quarter of that of the United States.

Activated carbon gold absorption effect

CLM
However, there are also some disadvantages :(1) it is highly corrosive to equipment; (2) it pollutes the environment, etc., which makes the chemical method limited to a certain extent. There are many researches on activation by adding H3P04 at home and abroad. In China, the development and research work of preparing activated carbon by using phosphoric acid method with wood chips as raw material has been carried out since the end of 1980s,It has been successfully put into industrial application in the 1990s,The mesopore (transition pore) structure of products produced by phosphoric acid activation method is well developed and has wide application fields.A kind of activated carbon material suitable for oil and gas recovery system by adsorption method was selected according to the design requirements. The main equipment of oil and gas recovery system by activated carbon adsorption method, the activated carbon tank, is designed and calculated, and its strength is checked. The flowchart of the oil and gas recovery system by activated carbon adsorption in the laboratory of Environmental Engineering Department is also drawn, and the system is simulated in three dimensional. Finally, the economic and technical analysis of activated carbon oil and gas recovery technology is carried out, and it is considered that the application of activated carbon adsorption oil and gas recovery system will bring obvious social benefits, bulk powdered activated charcoalenvironmental benefits and economic benefits, and has a wide application prospect.Deep desulfurization of transportation fuels is receiving increasing attention in theresearch community worldwide due to increasingly stringent regulations and fuelspecifications in many countries for environmental protection purpose. The traditionalhydrodesulfurization process (HDS) is highly efficient in removing thiols and sulfides, but itis less effective for thiophenes and thiophene derivatives. Ultra-deep desulfurization isbecoming even more formidable challenge for HDS with the decreasing lower sulfur in fuels.Therefore, non-hydrodesulfurization technique of liquid fuels has caused intensive concernsfor ultra-deep desulfurization. Recently, the adsorption desulfurization technique and catalyticoxidation-adsorption desulfurization technique have drawn much attention at home andabroad due to its mild reaction condition,low production cost and little environmentalpollutioz. This thesis focuses on the researches of application of activated carbon fiber inadsorption and oxidation-adsorption removal of thiophenic sulfur compounds from oils.www.wyactivatedcarbon.com

Coconut husks are widely used in wine

CLM
In domestic has been eliminated. Specific surface area test unified the multi-point BET method at home and abroad, specific surface area measurement standards are developed at home and abroad is based on BET test method, please see our national standard (GB/T 19587-2004) - gas adsorption BET principle of solid material specific surface area measurement methods. Specific surface area testing is actually the more time-consuming jobs, as the adsorption capacity of sample is different, some sample testing may need to spend the whole dayTime, if the test process is not fully automated, the tester can not leave at any time, and should be highly focused, observe the dashboard, control the knob, a little careless will lead to the failure of the test process, which will waste a lot of valuable time of the tester. F - Sorb 2400 specific surface tester is really able to BET method detection instruments (both direct comparison method), the more important F - Sorb 2400 specific surface tester is by far the only specific surface area of the fully automated intelligent testing equipment, the test results with the international high consistency, the stability is very good also, at the same time reduce the human error, improve accuracy test results."Activated carbon production and construction project" belongs to zhoukou xyz co., ltd. plans in zhoukou economic development zone (new) projects, proposed the project the total area of 25072.53 square meters about 37.59 acres), is expected to total investment of 95.0984 million yuan, including: investment in fixed assets of 83.8144 million yuan, flow capital of 11.284 million yuan, is expected to comprehensive income for 94.17 million yuan.activated charcoal manufacturers The economic situation this year is generally characterized by a steady but positive trend, and more positive changes have taken place in economic development. Stability is reflected in the fact that the economy performed within an appropriate range, growth became more stable, and the quality and performance of the economy continued to improve. The economic structure has continued to improve. Innovation is playing an increasingly important role in underpinning development. The service sector accounts for a larger share of the economy, and consumption is contributing more to growth.gold recovery activated carbon Stability is also reflected in new breakthroughs in reform and opening up.

Material level of activated carbon

CLM
Industry, agriculture and many other fields. In recent years, one of the research hotspots of activated carbon is to use cheap agricultural and forestry wastes as raw materials and simple and clean process to prepare biomass activated carbon with high economic benefit and good adsorption performance.[url=https://www.yrdcarbon.com/products/]activated charcoal manufacturers[/url] If the agricultural and forestry wastes are effectively utilized and turned into treasures, it can not only create certain economic benefits, but also reduce its pollution to the environment, and achieve the purpose of treating waste with waste. In this paper, using biomass (corn cob, rice husk and peanut shell) as raw material, the experimental research on the preparation of activated carbon from biomass was carried out on the self-built experimental platform, and the activation temperature, activation time, impregnation ratio and impregnation time and other activation and physicochemical characteristics were systematically studied.The granular activated carbon with high strength was prepared by heating wood phosphate mixture at low temperature and using tar generated during its pyrolysis as binder.[url=https://www.yrdcarbon.com/news/coconut-shell-activated-carbon-for-gold-recovery.html]gold recovery activated carbon[/url] In this paper, the process conditions and plasticizing mechanism of granular activated carbon prepared by phosphoric acid were studied, which provided scientific data and theoretical basis for the preparation of high strength granular activated carbon. Fir chip as the raw materials, H - POs as activator, using single factor analysis and orthogonal experimental design method, this paper discusses the influence granular activated carbon pore structure and the iodine adsorption value, methylene blue and strength of various preparation factors, determine the optimum process conditions of preparation of granular activated carbon phosphoric acid, phosphoric acid concentration is 70%, dipping 180%, kneading temperature is 170 ℃, for 60 min kneading time, activation temperature is 350 ℃, the activation time of 210 min. The iodine adsorption value, methylene blue adsorption value, strength and BET specific surface area of GAC were 1020.04mGG, 225mg/g, 88.73% and 1486.48m2/g respectively. The experimental results show that the impregnation ratio and carbon activation temperature have great effects on the adsorption performance of GAC, while the kneading temperature and impregnation ratio have great effects on the strength of GAC.Because the strength of GAC decreases with the increase of impregnation ratio, and the decrease range is large, so the preparation of GAC with compound activator is proposed.